Lasermax LMS-XDMS User Manual
Browse online or download User Manual for Optical devices Lasermax LMS-XDMS. LaserMax LMS-XDMS User Manual
- Page / 2
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installing your LaserMax Guide Rod Laser
: e laser may turn on when installed properly in the slide. Always make sure
the sight is pointed in a safe direction. To avoid improper laser seating, put the slide
upside down on a at surface when installing your Guide Rod Laser. Remove the factory
guide rod and store for future use.
XDM 4.5”
Insert recoil spring provided into circular opening in the front of the slide.
Next, insert the LaserMax Guide Rod Laser into the opposite end of the spring
with engraved text facing up away from barrel.
Applying forward pressure to compress spring, seat round side of battery cap
marked with ‘’ (arrows point toward barrel) in the crescent notch of barrel lug.
e at cap top should be centered and parallel with at top of the lug ( ).
XD 3”
Firmly grasp the assembled sight by the battery cap and insert the assembly into
the slide while pushing forward and down. e battery contact on the battery cap
is slightly o–center. e square side of the battery cap closest to the contact
should be away from the barrel ( ). Seat the Guide Rod Laser all the way
down on the barrel, as you would the factory guide rod.
XDM 4.5”/ XD 3”
With the magazine still removed, reassemble the slide to the frame by
pulling the slide to the rear. Rotate the takedown lever to return it to the horizontal
position and release the slide stop lever.
Cycle the action. e slide lock should return to the top of the slide lock notch.
If resistance is felt during assembly, do not force. Remove the slide and make sure
that the laser assembly is positioned as required, then attempt assembly again.
Cycle the slide fully several times allowing the slide to go forward under
full pressure of the recoil spring to make sure that the sight is seated in the frame.
Compare your laser sight to your iron sights to insure proper installation.
at’s it! Now test your new LaserMax Guide Rod Laser.
OPERATION
XDM 4.5”
Rotate the teardrop shaped switch ° clockwise on the takedown lever located on the le
side of the rearm to turn laser on. Notice: e red dot on the switch indicates the laser
is on.
Note: the laser sight should be projecting a pulsating red beam that closely matches the
Point of Aim () of the factory open sights.
Rotate the teardrop shaped switch ° counterclockwise,
back to the orginal position to turn laser o.
XD 3”
Push in the takedown lever/laser switch with the trigger nger until a click is felt.
e red mark on the switch will be visible.
Your Guide Rod Laser is factory aligned and no further alignment is needed.
Your point of bullet impact should be within 1½” of your point of laser aim at yards.
IMPORTANT: LASERMAX, INC. DOES NOT WARRANTY THE ALIGNMENT
OR FUNCTION OF THE GUIDE ROD LASER FOR PORTED FIREARMS, OR FOR
FIREARMS WHICH HAVE BEEN ALTERED FROM FACTORY CONFIGURATION.
DANGER–Laser radiation is emitted from the front aperture of the laser when the switch is
activated. Please read the warning labels found in this manual.
Before handling any rearm with or without a laser, read and understand the entire contents
of your rearm and laser manual, especially the safety precautions and procedures for safe
rearms handling.
Follow all precautions as outlined by the rearms manufacturer. Keep this and all rearm
related products locked and secured from children or other unauthorized users. Safety glasses
are recommended during all steps of assembly and disassembly.
Always make sure the weapon is clear and safe before attempting to install or uninstall
your laser or making adjustments or changing laser batteries. Never put your hand in
front of the muzzle of a rearm. Always keep your nger away from the trigger until you
are ready to re. Test your LaserMax laser periodically during periods of non-usage to
ensure adequate battery levels.
LaserMax, Inc. strongly recommends that the user of the rearm install the sight.
e Guide Rod Laser becomes an integral part of the rearm, and the user should
become familiar with its installation and use as with the rest of the rearm.
Initial Inspection
If the shipping package is severely damaged, notify the carrier immediately for
insurance purposes.
Installation
e LaserMax Guide Rod Laser is designed to be used with the Springeld Armory rearm,
lubricated exactly as described in the current version of the Springeld Armory Owner’s
Manual. Excess lubricant can interfere with the proper function of both the rearm and the
Guide Rod Laser, as can inadequate lubricant.
Field Strip Your Firearm
Please refer to your owners manual for instructions on eld stripping
and rearms safety.
Remove Factory Takedown Lever
Removing the factory lever and installing ours both require substantial force.
TOOLS SHOULD NOT BE USED. Remove the factory takedown lever from frame by
twisting it counter-clockwise while pulling the lever away from the frame until
switch pulls out ( ). Store with factory guide rod for future use.
Install the LaserMax Takedown Lever/Activation Switch
Insert the LaserMax lever/switch with the “ag” pointing at the : position. Firmly push in
towards the frame while twisting counter-clockwise to :, then to :, then back to :
and push in on switch to lock it in and make it ush with the frame ( ). e .”
takedown activation switch will click into position when properly seated. e ” will seat
itself when properly installed.
Test the action of the new laser switch. For the ”, push the switch in towards the frame.
ere will be a ‘click’ felt when the switch is in the ‘on’ position. Test both directions as the
switch is ambidextrous. For the .”, rotate the teardrop shaped lever 90°. You will feel a
distinct ‘click’ when the lever has been properly rotated.
Installing batteries and battery cap
XDM 4.5”
Gently pop the cap o the laser tube to expose the batteries.
Replace batteries with a new set. Make sure the at inscribed end (+) of the batteries
is facing toward you.
With the recessed notch on the laser tube at the : position, place the battery cap
raised notch at the : position, insert the opposite end of the cap into the battery
compartment rst. en push in while twisting the cap clockwise and you will feel
the cap snap into place and seat.
e cap will lay ush to the tube. If a gap exists, the -ring did not seat properly.
Remove the cap and perform above step again.
XD 3”
Slide cap o of the end. Insert a new LaserMax battery pack into the battery compartment
with the at side (+) facing out of the tube. Slide the battery cap back onto the tube.
e word ‘’ is engraved on both the laser tube and the cap with indicating arrows.
e arrows on the tube and cap must point the same way. Incorrect installation will
cause signicant alignment error between the lasers point of aim and the bullet’s point
of impact. Be sure the gold–plated battery contact is pressed rmly into its recess
on the mating side of the cap. Hold the battery pack below the surface of the battery
compartment with a ngernail while sliding the cap into position.
1
2
3
4
GUIDE ROD LASER
User Guide for Springfield XDM 4.5” (9mm/.40 S&W ONLY)
Springfield XD 3” (9mm/.40 S&W ONLY)
See it installed at
www.LaserMax.com or find it on
Part # 01785–0–33( ) /
Please read this entire manual before you begin the
installation of your new LaserMax Guide Rod Laser.
5
1
2
Summary of Contents
Page 1 - GUIDE ROD LASER
Installing your LaserMax Guide Rod Laser: e laser may turn on when installed properly in the slide. Always make sure the sight is pointed in a
Page 2 - REMINDER
Warranty Information Registration of your product is required in order to receive warranty service. Log on to www.lasermax.com to fill out the registr
© 2020, manymanuals.com. All rights reserved. | 1.152 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals