Lasermax LMS-1441 User Manual
Browse online or download User Manual for Optical devices Lasermax LMS-1441. LaserMax LMS-1441 User Manual
- Page / 2
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installing your LaserMax Guide Rod Laser
Slide the factory recoil spring onto the Guide Rod Laser making sure the accuracy
washer is in place on the guide rod.
With the short legs of the battery cap facing the barrel, rmly grasp the battery
cap and insert the assembly into the slide while pushing forward and down. When
installing the Guide Rod Laser, be sure that the legs on the battery cap of the
Guide Rod Laser rests centered and at against the bottom of the front barrel lug
as shown in gure 4 & 5.
With the magazine still removed, reassemble the slide to the frame. Pull the
slide ¼” past the barrel locked position and rotate the disassembly latch to the
horizontal position as shown in gure 6. If resistance is felt during assembly, do
not force. Remove the slide, ensure that the cap and short legs are positioned as
required, then attempt assembly again.
Cycle the slide fully several times allowing the slide to go forward under full
pressure of the recoil spring to make sure that the Guide Rod Laser is seated in the
frame.
at’s it! Now test your new LaserMax Guide Rod Laser.
OPERATION
Point the pistol in a safe direction. To activate the laser, push in the disassembly
latch/laser switch pin with your trigger nger until a click is felt. A red indication
mark will be visible from the opposite side.
e laser should be projecting a pulsing red beam that closely matches the
factory open sight.
Turn the laser sight o by recentering the disassembly latch/laser switch, pressing
in the opposite direction until the red on indicator is no longer visible.
Pressing the disassembly latch/laser switch further will turn the sight on again
and expose the red on indicator.
IMPORTANT: LASERMAX, INC. DOES NOT WARRANTY THE ALIGNMENT
OR FUNCTION OF THE GUIDE ROD LASER FOR PORTED FIREARMS, OR FOR
FIREARMS WHICH HAVE BEEN ALTERED FROM FACTORY CONFIGURATION.
DANGER–Laser radiation is emitted from the front aperture of the laser when the switch is
activated. Please read the warning labels found in this manual.
Before handling any rearm with or without a laser, read and understand the entire contents
of your rearm and laser manual, especially the safety precautions and procedures for safe
rearms handling.
Follow all precautions as outlined by the rearms manufacturer. Keep this and all rearm
related products locked and secured from children or other unauthorized users. Safety glasses
are recommended during all steps of assembly and disassembly.
Always make sure the weapon is clear and safe before attempting to install or uninstall
your laser or making adjustments or changing laser batteries. Never put your hand in
front of the muzzle of a rearm. Always keep your nger away from the trigger until you
are ready to re. Test your LaserMax laser periodically during periods of non-usage to ensure
adequate battery levels.
LaserMax, Inc. encourages the user of the rearm to install the sight.
e Guide Rod Laser becomes an integral part of the rearm, and the user should
become familiar with its installation and use as with the rest of the rearm.
Initial Inspection
If the shipping package is severely damaged, notify the carrier immediately for
insurance purposes.
Installation
e LaserMax Guide Rod Laser is designed to be used with the Beretta or Taurus rearm.
Lubricate your pistol exactly as described in the current version of the Beretta or Taurus Owner’s
Manual. Excessive or inadequate lubrication can interfere with the proper function of both the
rearm and the Guide Rod Laser.
Field Strip Your Firearm
Please refer to your owners manual for instructions on eld stripping and
rearms safety.
Removing Factory Disassembly Latch
Hold the pistol frame in the right hand and with the right forenger, depress the
disassembly latch release button (gure 1). Continue to hold this button in throughout the
installation of the disassembly latch. With the le hand rotate the disassembly latch counter
clockwise until the lever stops. Pull the disassembly latch outward and remove the latch
from the frame (gure 2).
NOTE: You should use the disassembly latch release button and spring provided by the
rearms manufacturer and the disassembly latch provided by LaserMax.
Install the LaserMax Disassembly Latch/Laser Switch
Hold the frame of the pistol in the right hand with the right side of the frame facing upward.
While still holding the release button in, place the LaserMax disassembly latch into the le
side of the frame and rotate it clockwise until it stops against the release button. Make sure the
disassembly latch is under the end of the release button (gure 3).
e center notch in the laser switch should be centered in the frame before
the slide assembly is installed.
Removal of the Factory Guide Rod
Grasp the recoil spring and with forceful control, slide it forward about ½” and li it out of the
slide.
Remove the spring and guide. Place the guide rod in storage. You will be using the factory spring
with the Guide Rod Laser.
Installation of New Batteries
Your LaserMax Guide Rod Laser comes with a new battery pack pre–installed. Installation or
replacement of the battery set is accomplished by removal of the battery cap from the rear of the
Guide Rod Laser. Hold the Guide Rod Laser in the le hand, and with the right hand push the
cap onto the Guide Rod Laser and simultaneously rotate the cap counter clockwise to remove
it. Replace the batteries with a new set with the plus (+) facing out. Now replace the battery
cap by aligning painted tab with painted notch on cap (only one position is possible), pressing
down and rotating the cap clockwise. Note: Some resistance will be felt rotating the cap until it is
locked into position.
*See reverse side of this installation guide for reference photos.
1
2
3
4
5
GUIDE ROD LASER
User Guide for Beretta 92 & 96 Full Size and
Taurus PT 92, 99, 100, & 101
See it installed at
www.LaserMax.com or find it on
Part # 01785–0–4( ) /
Please read this entire manual before you begin the
installation of your new LaserMax Guide Rod Laser.
6
1
2
Summary of Contents
Page 1 - GUIDE ROD LASER
Installing your LaserMax Guide Rod LaserSlide the factory recoil spring onto the Guide Rod Laser making sure the accuracy washer is in place on the gu
Page 2 - REMINDER
Warranty Information Registration of your product is required in order to receive warranty service. Log on to www.lasermax.com to fill out the registr
Related products and manuals for Optical devices Lasermax LMS-1441
(2 pages)© 2020, manymanuals.com. All rights reserved. | 0.313 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals